Difference between revisions of "Colibri"

From Stm32World Wiki
Jump to navigation Jump to search
 
(41 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[Category:Colibri]][[Category:Work in progress]]{{metadesc|Colibri Automation System}}
 
[[Category:Colibri]][[Category:Work in progress]]{{metadesc|Colibri Automation System}}
−
[[File:colibri_2-RevA-front3d-2.png|thumb|200px]]
+
 
 +
[[File:colibri_2-RevA-front3d-2.png|thumb|250px]]
 +
[[File:Colibri-3-6.jpg|thumb|250px]]
 +
[[File:Colibri rs485u-2.jpg|180px|thumb]]
 +
[[File:Colibri aic-RevA-2.jpg|180px|thumb]]
 +
 
 
[[Colibri]] is a low-cost automation system, primarily intended for building automation, home automation, energy supervision, agriculture supervision and similar systems. Main features beside costs are;
 
[[Colibri]] is a low-cost automation system, primarily intended for building automation, home automation, energy supervision, agriculture supervision and similar systems. Main features beside costs are;
−
* Flexible I/O system, via Expansion Cards in M.2 Key E sockets.
+
* Flexible I/O system, via Expansion Cards in M.2 Key E sockets. Many types already developed.
 
* Power supply of 9-36 Volt, either AC or DC (some expansion cards won't work with DC supply)
 
* Power supply of 9-36 Volt, either AC or DC (some expansion cards won't work with DC supply)
−
* Colibri-1 using LoraWAN for communications.
+
* Each I/O slot can be powered-up/down individually from the MCU.
−
* Colibri-2 is a full-fledged Raspberry Pi, built with Compute Module 4 (CM4)
+
* Each I/O slot is addressable individually.
 +
* Each expansion module has an EEPROM with program and calibration parameters for the MCU module to use.
 +
* Some expansion modules have on-board secondary processors for time-critical or other reasons, for instance pulse counting and PID regulator.
 +
 
 +
 
 +
== Carrier Boards ==
 +
* Colibri-3 using LoraWAN for communications and 2 I/O expansion slots.
 +
* Planned; Colibri-8 is like the Colibri-3, but with 7 I/O expansion slots.
 +
* Planned; Colibri-7pi is a full-fledged Raspberry Pi, built with Compute Module 4 (CM4) and 7 I/O expansion slots.
 +
 
 +
== MCU Modules ==
 +
There is a choice, and more will follow;
 +
 
 +
* [[Colibri MCU1]] - RAK3172 which has a STM32WLE5, 256kB Flash, 64kB RAM, on-chip LoRa and LoraWAN protocol available from GitHUb.
 +
* [[Colibri MCU2]] - ESP32-S3-Mini-1-N4R2 which is intended for [https://esphome.io ESPhome] applications. On-board PCB WiFi antenna.
 +
* [[Colibri MCU3]] - ESP32-S3-Mini-1-N8 which is intended for [https://esphome.io ESPhome] applications. IPEX/U.FL antenna connector.
 +
 
 +
== Expansion Modules ==
 +
The Colibri system is based around the M.2 connector and a non-standard bus for I2C and SPI communications. Each expansion board has a EEPROM memory available to identify which module is present in each expansion slot. Furthermore, there is a [[Colibri Forth]] program located in the eeprom that contains the functionality of the module, executed in the MCU module. This allows for future expansion modules without requiring the upgrade of the MCU module.
 +
 
 +
NOTE; Colibri Forth is only available/supported for the Colibri MCU1 at the moment. Porting to other MCUs might or might not happen in the future.
  
 
== [[Colibri Form Factor|Form Factor]] ==
 
== [[Colibri Form Factor|Form Factor]] ==
Line 13: Line 38:
 
'''WARNING!!! Do NOT plug Colibri expansion boards into other equipment. Do NOT plug any M.2 card into a Colibri system, unless that card/board is specifically made for Colibri.'''
 
'''WARNING!!! Do NOT plug Colibri expansion boards into other equipment. Do NOT plug any M.2 card into a Colibri system, unless that card/board is specifically made for Colibri.'''
  
−
== Planned Boards ==
+
== Boards ==
  
 
{| class=wikitable
 
{| class=wikitable
 
|-
 
|-
−
!
 
 
! Name
 
! Name
 
! Type
 
! Type
Line 23: Line 47:
 
! Status
 
! Status
 
|-
 
|-
−
| [[File:colibri-1-RevB-front3d.png|220px]][[File:colibri-1-RevB-box.png|220px]]
+
| [[Colibri-3]]  
−
| [[Colibri-1]]  
+
| Colibri Carrier
−
| Colibri Host
+
| Minimal Colibri Host with 2 expansion cards. MCU slot is to be populated with any of the MCU variants available.
−
| Minimal Colibri Host with 2 expansion cards. MCU slot is to be populated with [https://dragino.com/products/lora/item/127-lora-st.html Dragino LoRaSt module].
+
| Prototype available
−
| Prototyping on-going
 
 
|-
 
|-
−
| [[File:colibri-2-RevA-front3d.png|220px]]
+
| [[M2 E Breakout]]
−
| [[Colibri-2]]  
+
| M2 breakout board
−
| Colibri Host
+
| Generic breakout board for M.2 E key boards.
−
| Colibri Host with 7 expansion cards, two Ethernet ports, 4 USB ports and SDcard connector.
+
| Available for pre-orders
−
| Ready for prototype
+
|-
 +
| [[Colibri Dev]]  
 +
| I/O Expansion
 +
| Development, maker, experimentation and breakout board for the Colibri I/O system. Power rails, 24LCxx dedicated footprint, plus i2c and spi on large pads.
 +
| Available for pre-orders
 
|-
 
|-
−
| [[File:Colibri aic-RevA-2.jpg|220px]][[File:Colibri aic-RevA-1.jpg|220px]]
 
 
| [[Colibri AIC]]
 
| [[Colibri AIC]]
 
| I/O Expansion
 
| I/O Expansion
 
| Two analog 0-20mA inputs
 
| Two analog 0-20mA inputs
−
| Prototyping on-going
+
| Prototype available
 
|-
 
|-
−
| [[File:Colibri aiv-RevA-2.jpg|220px]] [[File:Colibri aiv-RevA-1.jpg|220px]]
 
 
| [[Colibri AIV]]
 
| [[Colibri AIV]]
 
| I/O Expansion
 
| I/O Expansion
 
| Two analog 0-10V inputs
 
| Two analog 0-10V inputs
−
| Prototyping on-going
+
| Prototype available
 
|-
 
|-
−
| [[File:colibri_aqv-RevA-front3d.png|220px]] [[File:colibri_aqv-RevA-back3d.png|220px]]
 
 
| [[Colibri AQV]]
 
| [[Colibri AQV]]
 
| I/O Expansion
 
| I/O Expansion
 
| Two analog 0-10V outputs
 
| Two analog 0-10V outputs
−
| Prototyping on-going
+
| Prototype available
 
|-
 
|-
−
| [[Colibri diu-2.jpg|220px]] [[File:Colibri diu-1.jpg|220px]]
 
 
| [[Colibri DIU]]
 
| [[Colibri DIU]]
 
| I/O Expansion
 
| I/O Expansion
 
| Four digital inputs, for state, counter, pulsewidth measurement. On-board STM32F030 for ability to count very fast pulses and high accuracy PWM measurements.
 
| Four digital inputs, for state, counter, pulsewidth measurement. On-board STM32F030 for ability to count very fast pulses and high accuracy PWM measurements.
−
| Ready for prototype
+
| Prototype available
 +
|-
 +
| [[Colibri DII]]
 +
| I/O Expansion
 +
| Two ISOLATED digital inputs, for state, counter, pulsewidth measurement. On-board STM32F030 for ability to count very fast pulses and high accuracy PWM measurements.
 +
| Prototype available
 +
|-
 +
| [[Colibri RS485U]]
 +
| I/O Expansion
 +
| Two non-isolated RS-485 ports. On-board STM32F030 implementing Modbus protocol, either as master or slave device.
 +
| Prototype available
 
|-
 
|-
−
| [[File:colibri_pid-RevA-front3d.png|220px]] [[File:colibri_pid-RevA-back3d.png|220px]]
 
 
| [[Colibri PID1]]
 
| [[Colibri PID1]]
 
| I/O Expansion
 
| I/O Expansion
 
| PID regulator, with a PT1000 input and a 0-10V analog output. On-board STM32F030 for host-independent operation.
 
| PID regulator, with a PT1000 input and a 0-10V analog output. On-board STM32F030 for host-independent operation.
−
| Ready for prototype
+
| Prototype available
 
|-
 
|-
−
| [[File:colibri_pt1000-RevA-front3d.png|220px]] [[File:colibri_pt1000-RevA-back3d.png|220px]]
 
 
| [[Colibri Pt1000]]
 
| [[Colibri Pt1000]]
 
| I/O Expansion
 
| I/O Expansion
 
| Two PT1000 temperature sensor inputs.
 
| Two PT1000 temperature sensor inputs.
−
| Ready for prototype
+
| Prototype available
 
|-
 
|-
−
| [[File:Colibri rs485u-1.jpg|220px]] [[File:Colibri rs485u-2.jpg|220px]]
 
−
| [[Colibri RS485U]]
 
−
| I/O Expansion
 
−
| Two non-isolated RS-485 ports. On-board STM32F030 implementing Modbus protocol, either as master or slave device.
 
−
| Ready for prototype
 
−
|-
 
−
| [[File:colibri_ssr-RevA-front3d.png|220px]] [[File:colibri_ssr-RevA-back3d.png|220px]]
 
 
| [[Colibri SSR]]
 
| [[Colibri SSR]]
 
| I/O Expansion
 
| I/O Expansion
 
| Two Solid State Relays, ON/OFF.
 
| Two Solid State Relays, ON/OFF.
−
| Ready for prototype
+
| Prototype available
 
|-
 
|-
−
| [[File:Colibri triac1-1.jpg|220px]] [[File:Colibri triac1-2.jpg|220px]]
 
 
| [[Colibri TRIAC1]]
 
| [[Colibri TRIAC1]]
 
| I/O Expansion
 
| I/O Expansion
 
| Four Triac outputs, driving 24V AC.
 
| Four Triac outputs, driving 24V AC.
 +
| Prototype available
 +
|-
 +
| [[Colibri MCU1]]
 +
| Host MCU
 +
| MCU module for the Colibri-3 and similar carrier boards with LoraWAN. Contains RAK3172 with 256kB Flash and 64kB RAM.
 +
| Prototype available.
 +
|-
 +
| [[Colibri MCU2]]
 +
| Host MCU
 +
| MCU module for the Colibri-3 and similar carrier boards with LoraWAN. Contains ESP32-S3-Mini1-N4R2.
 +
| Prototype available.
 +
|-
 +
| [[Colibri MCU3]]
 +
| Host MCU
 +
| MCU module for the Colibri-3 and similar carrier boards with WiFi. Contains ESP32-S3-Mini1U-N8.
 +
| Prototype available.
 +
|}
 +
 +
== Planned Boards ==
 +
 +
{| class=wikitable
 +
|-
 +
!
 +
! Name
 +
! Type
 +
! Description
 +
! Status
 +
|-
 +
| [[File:colibri-2-RevA-front3d.png|180px]]
 +
| [[Colibri-7pi]]
 +
| Colibri Carrier
 +
| Colibri carrier board with 7 expansion cards, two Ethernet ports, 4 USB ports and SDcard connector. Powered by Raspberry Pi CM5 module.
 
| Ready for prototype
 
| Ready for prototype
 +
|-
 +
|
 +
| [[Colibri-8]]
 +
| Colibri Carrier
 +
| Colibri carrier board with 7 expansion cards, similar to [[Colibri-3]] but with a different size and enclosure.
 +
| Planned
 
|}
 
|}
 +
 +
= License =
 +
All Schematics and PCB layout are licensed with the GPLv3, meaning that you are free to make your own designs or manufacture devices using these. We expect that if you derive new design, that you publish these, preferably on this website.
 +
 +
The software will also be published with GPLv3, when something is workable.
  
 
= Resources =
 
= Resources =
−
* Dragino LoRa ST software stack; https://github.com/dragino/LoRa_STM32
+
[https://docs.rakwireless.com/Product-Categories/WisDuo/RAK3172-Module/Overview RAK3172 Product Page]
−
* Dragino LoRa ST hardware; https://github.com/dragino/Lora/tree/master/LoRaST
+
 
 +
[https://docs.rakwireless.com/Introduction/ RAKwireless documentation site]

Latest revision as of 10:10, 17 November 2024


Colibri 2-RevA-front3d-2.png
Colibri-3-6.jpg
Colibri rs485u-2.jpg
Colibri aic-RevA-2.jpg

Colibri is a low-cost automation system, primarily intended for building automation, home automation, energy supervision, agriculture supervision and similar systems. Main features beside costs are;

  • Flexible I/O system, via Expansion Cards in M.2 Key E sockets. Many types already developed.
  • Power supply of 9-36 Volt, either AC or DC (some expansion cards won't work with DC supply)
  • Each I/O slot can be powered-up/down individually from the MCU.
  • Each I/O slot is addressable individually.
  • Each expansion module has an EEPROM with program and calibration parameters for the MCU module to use.
  • Some expansion modules have on-board secondary processors for time-critical or other reasons, for instance pulse counting and PID regulator.


Carrier Boards

  • Colibri-3 using LoraWAN for communications and 2 I/O expansion slots.
  • Planned; Colibri-8 is like the Colibri-3, but with 7 I/O expansion slots.
  • Planned; Colibri-7pi is a full-fledged Raspberry Pi, built with Compute Module 4 (CM4) and 7 I/O expansion slots.

MCU Modules

There is a choice, and more will follow;

  • Colibri MCU1 - RAK3172 which has a STM32WLE5, 256kB Flash, 64kB RAM, on-chip LoRa and LoraWAN protocol available from GitHUb.
  • Colibri MCU2 - ESP32-S3-Mini-1-N4R2 which is intended for ESPhome applications. On-board PCB WiFi antenna.
  • Colibri MCU3 - ESP32-S3-Mini-1-N8 which is intended for ESPhome applications. IPEX/U.FL antenna connector.

Expansion Modules

The Colibri system is based around the M.2 connector and a non-standard bus for I2C and SPI communications. Each expansion board has a EEPROM memory available to identify which module is present in each expansion slot. Furthermore, there is a Colibri Forth program located in the eeprom that contains the functionality of the module, executed in the MCU module. This allows for future expansion modules without requiring the upgrade of the MCU module.

NOTE; Colibri Forth is only available/supported for the Colibri MCU1 at the moment. Porting to other MCUs might or might not happen in the future.

Form Factor

Colibri expansion boards are 22x42mm and has an edge connector called M.2 Key E. Many of the pins are following the Key E standard, but Colibri boards have additional requirements, which is not available in the official standard.

WARNING!!! Do NOT plug Colibri expansion boards into other equipment. Do NOT plug any M.2 card into a Colibri system, unless that card/board is specifically made for Colibri.

Boards

Name Type Description Status
Colibri-3 Colibri Carrier Minimal Colibri Host with 2 expansion cards. MCU slot is to be populated with any of the MCU variants available. Prototype available
M2 E Breakout M2 breakout board Generic breakout board for M.2 E key boards. Available for pre-orders
Colibri Dev I/O Expansion Development, maker, experimentation and breakout board for the Colibri I/O system. Power rails, 24LCxx dedicated footprint, plus i2c and spi on large pads. Available for pre-orders
Colibri AIC I/O Expansion Two analog 0-20mA inputs Prototype available
Colibri AIV I/O Expansion Two analog 0-10V inputs Prototype available
Colibri AQV I/O Expansion Two analog 0-10V outputs Prototype available
Colibri DIU I/O Expansion Four digital inputs, for state, counter, pulsewidth measurement. On-board STM32F030 for ability to count very fast pulses and high accuracy PWM measurements. Prototype available
Colibri DII I/O Expansion Two ISOLATED digital inputs, for state, counter, pulsewidth measurement. On-board STM32F030 for ability to count very fast pulses and high accuracy PWM measurements. Prototype available
Colibri RS485U I/O Expansion Two non-isolated RS-485 ports. On-board STM32F030 implementing Modbus protocol, either as master or slave device. Prototype available
Colibri PID1 I/O Expansion PID regulator, with a PT1000 input and a 0-10V analog output. On-board STM32F030 for host-independent operation. Prototype available
Colibri Pt1000 I/O Expansion Two PT1000 temperature sensor inputs. Prototype available
Colibri SSR I/O Expansion Two Solid State Relays, ON/OFF. Prototype available
Colibri TRIAC1 I/O Expansion Four Triac outputs, driving 24V AC. Prototype available
Colibri MCU1 Host MCU MCU module for the Colibri-3 and similar carrier boards with LoraWAN. Contains RAK3172 with 256kB Flash and 64kB RAM. Prototype available.
Colibri MCU2 Host MCU MCU module for the Colibri-3 and similar carrier boards with LoraWAN. Contains ESP32-S3-Mini1-N4R2. Prototype available.
Colibri MCU3 Host MCU MCU module for the Colibri-3 and similar carrier boards with WiFi. Contains ESP32-S3-Mini1U-N8. Prototype available.

Planned Boards

Name Type Description Status
Colibri-2-RevA-front3d.png Colibri-7pi Colibri Carrier Colibri carrier board with 7 expansion cards, two Ethernet ports, 4 USB ports and SDcard connector. Powered by Raspberry Pi CM5 module. Ready for prototype
Colibri-8 Colibri Carrier Colibri carrier board with 7 expansion cards, similar to Colibri-3 but with a different size and enclosure. Planned

License

All Schematics and PCB layout are licensed with the GPLv3, meaning that you are free to make your own designs or manufacture devices using these. We expect that if you derive new design, that you publish these, preferably on this website.

The software will also be published with GPLv3, when something is workable.

Resources

RAK3172 Product Page

RAKwireless documentation site

Retrieved from "https://stm32world.com/w/index.php?title=Colibri&oldid=4848"