STM32MP157A-DK1
STM32MP157A-DK1 development board
Default Linux
Partitioning
Boot log
NOTICE: CPU: STM32MP157AAC Rev.B
NOTICE: Model: STMicroelectronics STM32MP157A-DK1 Discovery Board
NOTICE: Board: MB1272 Var1 Rev.C-01
INFO: Reset reason (0x15):
INFO: Power-on Reset (rst_por)
INFO: Using SDMMC
INFO: Instance 1
INFO: Boot used partition fsbl1
INFO: Product_below_2v5=1: HSLVEN update is
INFO: destructive, no update as VDD>2.7V
NOTICE: BL2: v2.0(debug):
NOTICE: BL2: Built : 13:13:37, Oct 2 2018
INFO: BL2: Doing platform setup
INFO: PMIC version = 0x10
INFO: RAM: DDR3-1066/888 bin G 1x4Gb 533MHz v1.41
INFO: Memory size = 0x20000000 (512 MB)
INFO: BL2 runs SP_MIN setup
INFO: BL2: Loading image id 4
INFO: Loading image id=4 at address 0x2fff0000
INFO: Image id=4 loaded: 0x2fff0000 - 0x30000000
INFO: BL2: Loading image id 5
INFO: Loading image id=5 at address 0xc0100000
INFO: STM32 Image size : 746647
WARNING: Skip signature check (header option)
INFO: Image id=5 loaded: 0xc0100000 - 0xc01b6497
INFO: read version 0 current version 0
NOTICE: BL2: Booting BL32
INFO: Entry point address = 0x2fff0000
INFO: SPSR = 0x1d3
INFO: PMIC version = 0x10
NOTICE: SP_MIN: v2.0(debug):
NOTICE: SP_MIN: Built : 13:13:37, Oct 2 2018
INFO: ARM GICv2 driver initialized
INFO: stm32mp HSI (18): Secure only
INFO: stm32mp HSE (20): Secure only
INFO: stm32mp PLL2 (27): Secure only
INFO: stm32mp PLL2_R (30): Secure only
INFO: SP_MIN: Initializing runtime services
INFO: SP_MIN: Preparing exit to normal world
U-Boot 2018.11-stm32mp-r2 (Nov 14 2018 - 16:10:06 +0000)
CPU: STM32MP157AAC Rev.B
Model: STMicroelectronics STM32MP157A-DK1 Discovery Board
Board: stm32mp1 in trusted mode (st,stm32mp157a-dk1)
Board: MB1272 Var1 Rev.C-01
Watchdog enabled
DRAM: 512 MiB
Clocks:
- MPU : 650 MHz
- MCU : 208.878 MHz
- AXI : 266.500 MHz
- PER : 24 MHz
- DDR : 533 MHz
NAND: 0 MiB
MMC: STM32 SDMMC2: 0
In: serial
Out: serial
Err: serial
Net: eth0: ethernet@5800a000
Boot over mmc0!
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:4...
Found U-Boot script /boot.scr.uimg
1553 bytes read in 1 ms (1.5 MiB/s)
## Executing script at c4100000
Scanning mmc 0:4...
Found /mmc0_stm32mp157a-dk1_extlinux/extlinux.conf
Retrieving file: /mmc0_stm32mp157a-dk1_extlinux/extlinux.conf
237 bytes read in 0 ms
Retrieving file: /mmc0_stm32mp157a-dk1_extlinux/../splash.bmp
46180 bytes read in 3 ms (14.7 MiB/s)
1: stm32mp157a-dk1-sdcard
Enter choice: 1: stm32mp157a-dk1-sdcard
Retrieving file: /uImage
6569168 bytes read in 290 ms (21.6 MiB/s)
append: root=/dev/mmcblk0p6 rootwait rw console=ttySTM0,115200
Retrieving file: /stm32mp157a-dk1.dtb
67753 bytes read in 4 ms (16.2 MiB/s)
## Booting kernel from Legacy Image at c2000000 ...
Image Name: Linux-4.19.9
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 6569104 Bytes = 6.3 MiB
Load Address: c2000040
Entry Point: c2000040
Verifying Checksum ... OK
## Flattened Device Tree blob at c4000000
Booting using the fdt blob at 0xc4000000
XIP Kernel Image ... OK
Using Device Tree in place at c4000000, end c40138a8
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.9 (oe-user@oe-host) (gcc version 8.2.0 (GCC)) #1 SMP PREEMPT Thu Dec 13 08:16:23 UTC 2018
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: STMicroelectronics STM32MP157A-DK1 Discovery Board
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] Reserved memory: created DMA memory pool at 0x10000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node mcuram2@0x10000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x10040000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vdev0vring0@10040000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x10042000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vdev0vring1@10042000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x10044000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@10044000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x30000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node mcuram@0x30000000, compatible id shared-dma-pool
[ 0.000000] Reserved memory: created DMA memory pool at 0x38000000, size 0 MiB
[ 0.000000] OF: reserved mem: initialized node retram@0x38000000, compatible id shared-dma-pool
[ 0.000000] cma: Reserved 128 MiB at 0xd4000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
[ 0.000000] random: get_random_bytes called from start_kernel+0xa0/0x494 with crng_init=0
[ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s40204 r8192 d21236 u69632
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113680
[ 0.000000] Kernel command line: root=/dev/mmcblk0p6 rootwait rw console=ttySTM0,115200
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 306152K/458752K available (10240K kernel code, 816K rwdata, 2860K rodata, 1024K init, 208K bss, 21528K reserved, 131072K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xdc800000 - 0xff800000 ( 560 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (11232 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 817 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 209 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] /soc/interrupt-controller@5000d000: bank0
[ 0.000000] /soc/interrupt-controller@5000d000: bank1
[ 0.000000] /soc/interrupt-controller@5000d000: bank2
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000026] Switching to timer-based delay loop, resolution 41ns
[ 0.001870] Console: colour dummy device 80x30
[ 0.001922] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.001947] pid_max: default: 32768 minimum: 301
[ 0.002185] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.002207] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.003215] CPU: Testing write buffer coherency: ok
[ 0.003710] CPU0: update cpu_capacity 1024
[ 0.003730] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059796] Setting up static identity map for 0xc0100000 - 0xc0100060
[ 0.079785] rcu: Hierarchical SRCU implementation.
[ 0.119931] smp: Bringing up secondary CPUs ...
[ 0.200524] CPU1: update cpu_capacity 1024
[ 0.200536] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200744] smp: Brought up 1 node, 2 CPUs
[ 0.200773] SMP: Total of 2 processors activated (96.00 BogoMIPS).
[ 0.200783] CPU: All CPU(s) started in SVC mode.
[ 0.201927] devtmpfs: initialized
[ 0.226453] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.226967] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.226998] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.233075] pinctrl core: initialized pinctrl subsystem
[ 0.235229] NET: Registered protocol family 16
[ 0.243163] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.245616] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.245638] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.245930] Serial: AMBA PL011 UART driver
[ 0.248074] stm32-pm-domain pm_domain: domain core-ret-power-domain registered
[ 0.248112] stm32-pm-domain pm_domain: subdomain core-power-domain registered
[ 0.248127] stm32-pm-domain pm_domain: domains probed
[ 0.262874] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOA bank added
[ 0.263222] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOB bank added
[ 0.263505] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOC bank added
[ 0.263773] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOD bank added
[ 0.264064] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOE bank added
[ 0.264340] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOF bank added
[ 0.264594] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOG bank added
[ 0.264871] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOH bank added
[ 0.265150] stm32mp157-pinctrl soc:pin-controller@50002000: GPIOI bank added
[ 0.265354] stm32mp157-pinctrl soc:pin-controller@50002000: Pinctrl STM32 initialized
[ 0.266190] stm32mp157-pinctrl soc:pin-controller-z@54004000: GPIOZ bank added
[ 0.266217] stm32mp157-pinctrl soc:pin-controller-z@54004000: Pinctrl STM32 initialized
[ 0.285817] stm32-mdma 58000000.dma: STM32 MDMA driver registered
[ 0.290830] SCSI subsystem initialized
[ 0.291603] usbcore: registered new interface driver usbfs
[ 0.291683] usbcore: registered new interface driver hub
[ 0.291821] usbcore: registered new device driver usb
[ 0.292149] pps_core: LinuxPPS API ver. 1 registered
[ 0.292162] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.292196] PTP clock support registered
[ 0.292469] EDAC MC: Ver: 3.0.0
[ 0.293379] Advanced Linux Sound Architecture Driver Initialized.
[ 0.295023] clocksource: Switched to clocksource arch_sys_counter
[ 0.388823] NET: Registered protocol family 2
[ 0.389868] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes)
[ 0.389920] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.389987] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.390084] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.390221] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.390268] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.390770] NET: Registered protocol family 1
[ 0.391743] RPC: Registered named UNIX socket transport module.
[ 0.391765] RPC: Registered udp transport module.
[ 0.391776] RPC: Registered tcp transport module.
[ 0.391786] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.392860] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[ 0.394918] Initialise system trusted keyrings
[ 0.395408] workingset: timestamp_bits=14 max_order=17 bucket_order=3
[ 0.406213] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.407331] NFS: Registering the id_resolver key type
[ 0.407378] Key type id_resolver registered
[ 0.407391] Key type id_legacy registered
[ 0.407604] ntfs: driver 2.1.32 [Flags: R/O].
[ 0.408099] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.408989] fuse init (API version 7.27)
[ 0.409679] pstore: using deflate compression
[ 0.412608] NET: Registered protocol family 38
[ 0.412636] Key type asymmetric registered
[ 0.412649] Asymmetric key parser 'x509' registered
[ 0.412749] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[ 0.412768] io scheduler noop registered
[ 0.412780] io scheduler deadline registered
[ 0.413055] io scheduler cfq registered (default)
[ 0.413071] io scheduler mq-deadline registered
[ 0.413084] io scheduler kyber registered
[ 0.414389] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.1
[ 0.414530] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.2
[ 0.414658] stm32-usbphyc 5a006000.usbphyc: Dropping the link to regulator.2
[ 0.414765] stm32-usbphyc 5a006000.usbphyc: Dropping the link to regulator.1
[ 0.419491] stm32-dma 48000000.dma: STM32 DMA driver registered
[ 0.421280] stm32-dma 48001000.dma: STM32 DMA driver registered
[ 0.500249] STM32 USART driver initialized
[ 0.501612] 40010000.serial: ttySTM0 at MMIO 0x40010000 (irq = 25, base_baud = 4000000) is a stm32-usart
[ 1.418278] console [ttySTM0] enabled
[ 1.422470] stm32-usart 40010000.serial: interrupt mode used for rx (no dma)
[ 1.428993] stm32-usart 40010000.serial: interrupt mode used for tx (no dma)
[ 1.461276] brd: module loaded
[ 1.475748] loop: module loaded
[ 1.483447] libphy: Fixed MDIO Bus: probed
[ 1.487611] CAN device driver interface
[ 1.492334] stm32-dwmac 5800a000.ethernet: PTP uses main clock
[ 1.496833] stm32-dwmac 5800a000.ethernet: no reset control found
[ 1.502856] stm32-dwmac 5800a000.ethernet: No phy clock provided...
[ 1.510209] stm32-dwmac 5800a000.ethernet: User ID: 0x40, Synopsys ID: 0x42
[ 1.516145] stm32-dwmac 5800a000.ethernet: DWMAC4/5
[ 1.521039] stm32-dwmac 5800a000.ethernet: DMA HW capability register supported
[ 1.528390] stm32-dwmac 5800a000.ethernet: RX Checksum Offload Engine supported
[ 1.535705] stm32-dwmac 5800a000.ethernet: TX Checksum insertion supported
[ 1.542568] stm32-dwmac 5800a000.ethernet: Wake-Up On Lan supported
[ 1.548946] stm32-dwmac 5800a000.ethernet: TSO supported
[ 1.554166] stm32-dwmac 5800a000.ethernet: TSO feature enabled
[ 1.560040] stm32-dwmac 5800a000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[ 1.568135] libphy: stmmac: probed
[ 1.573980] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 1.580182] usbcore: registered new interface driver pegasus
[ 1.585769] usbcore: registered new interface driver asix
[ 1.591071] usbcore: registered new interface driver ax88179_178a
[ 1.597210] usbcore: registered new interface driver cdc_ether
[ 1.603008] usbcore: registered new interface driver smsc75xx
[ 1.608842] usbcore: registered new interface driver smsc95xx
[ 1.614498] usbcore: registered new interface driver net1080
[ 1.620210] usbcore: registered new interface driver cdc_subset
[ 1.626144] usbcore: registered new interface driver zaurus
[ 1.631700] usbcore: registered new interface driver cdc_ncm
[ 1.638509] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.643865] ehci-platform: EHCI generic platform driver
[ 1.649619] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.655328] ohci-platform: OHCI generic platform driver
[ 1.661188] usbcore: registered new interface driver usb-storage
[ 1.671087] stm32_rtc 5c004000.rtc: rtc core: registered 5c004000.rtc as rtc0
[ 1.677176] stm32_rtc 5c004000.rtc: Date/Time must be initialized
[ 1.682880] stm32_rtc 5c004000.rtc: registered rev:1.2
[ 1.688625] i2c /dev entries driver
[ 1.712205] stm32f7-i2c 40012000.i2c: can't use DMA
[ 1.719300] sii902x 0-0039: Failed to get supply 'iovcc': -517
[ 1.724040] stm32f7-i2c 40012000.i2c: STM32F7 I2C-0 bus adapter
[ 1.750635] stm32f7-i2c 5c002000.i2c: can't use DMA
[ 1.756676] typec_stusb 1-0028: STUSB driver registered
[ 1.762282] stpmic1 1-0033: PMIC Chip Version: 0x10
[ 1.771495] BUCK1: supplied by regulator-dummy
[ 1.778468] BUCK2: supplied by regulator-dummy
[ 1.784930] BUCK3: supplied by regulator-dummy
[ 1.791854] BUCK4: supplied by regulator-dummy
[ 1.798388] LDO1: supplied by v3v3
[ 1.805910] LDO2: supplied by regulator-dummy
[ 1.812706] LDO3: supplied by vdd_ddr
[ 1.818842] LDO4: supplied by regulator-dummy
[ 1.823297] LDO5: supplied by regulator-dummy
[ 1.830231] LDO6: supplied by v3v3
[ 1.835996] VREF_DDR: supplied by regulator-dummy
[ 1.842446] BOOST: supplied by regulator-dummy
[ 1.846650] VBUS_OTG: supplied by bst_out
[ 1.850637] SW_OUT: supplied by bst_out
[ 1.855871] random: fast init done
[ 1.859828] input: pmic_onkey as /devices/platform/soc/5c002000.i2c/i2c-1/1-0033/5c002000.i2c:stpmic@33:onkey/input/input0
[ 1.870086] stm32f7-i2c 5c002000.i2c: STM32F7 I2C-1 bus adapter
[ 1.878958] stm_thermal 50028000.thermal: stm_thermal_probe: Driver initialized successfully
[ 1.889209] mmci-pl18x 58005000.sdmmc: Linked as a consumer to regulator.8
[ 1.894791] mmci-pl18x 58005000.sdmmc: mmc0: PL180 manf 53 rev2 at 0x58005000 irq 56,0 (pio)
[ 1.930359] sdhci: Secure Digital Host Controller Interface driver
[ 1.936236] sdhci: Copyright(c) Pierre Ossman
[ 1.939481] Synopsys Designware Multimedia Card Interface Driver
[ 1.946116] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.953778] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.959498] usbcore: registered new interface driver usbhid
[ 1.963955] usbhid: USB HID core driver
[ 1.970573] stm32-ipcc 4c001000.mailbox: ipcc rev:1.0 enabled, 6 chans, proc 0
[ 1.977483] stm32-rproc m4@0: wdg irq registered
[ 1.982336] remoteproc remoteproc0: m4 is available
[ 1.986783] vref: supplied by vdd
[ 1.989478] stm32-adc-core 48003000.adc: Linked as a consumer to regulator.4
[ 1.996412] stm32-adc-core 48003000.adc: Linked as a consumer to regulator.7
[ 2.012361] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.025154] mmc0: new high speed SDHC card at address aaaa
[ 2.030126] iio iio:device2: Can't get offset/scale: -517
[ 2.031029] mmcblk0: mmc0:aaaa SS16G 14.8 GiB
[ 2.038036] optee: probing for conduit method from DT.
[ 2.044180] optee: api uid mismatch
[ 2.057340] NET: Registered protocol family 17
[ 2.060357] can: controller area network core (rev 20170425 abi 9)
[ 2.061295] mmcblk0: p1 p2 p3 p4 p5 p6 p7
[ 2.066833] NET: Registered protocol family 29
[ 2.075126] can: raw protocol (rev 20170425)
[ 2.079333] can: broadcast manager protocol (rev 20170425 t)
[ 2.085165] can: netlink gateway (rev 20170425) max_hops=1
[ 2.091085] Key type dns_resolver registered
[ 2.094918] ThumbEE CPU extension supported.
[ 2.099105] Registering SWP/SWPB emulation handler
[ 2.104830] registered taskstats version 1
[ 2.107977] Loading compiled-in X.509 certificates
[ 2.138183] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.1
[ 2.144154] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.2
[ 2.151626] stm32-usbphyc 5a006000.usbphyc: Linked as a consumer to regulator.12
[ 2.159609] stm32-usbphyc 5a006000.usbphyc: registered rev:1.0
[ 2.166705] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_d not found, using dummy regulator
[ 2.174336] dwc2 49000000.usb-otg: Linked as a consumer to regulator.0
[ 2.180895] dwc2 49000000.usb-otg: 49000000.usb-otg supply vusb_a not found, using dummy regulator
[ 2.202305] dwc2 49000000.usb-otg: EPs: 9, dedicated fifos, 952 entries in SPRAM
[ 2.209964] ehci-platform 5800d000.usbh-ehci: EHCI Host Controller
[ 2.214735] ehci-platform 5800d000.usbh-ehci: new USB bus registered, assigned bus number 1
[ 2.223554] ehci-platform 5800d000.usbh-ehci: irq 60, io mem 0x5800d000
[ 2.255074] ehci-platform 5800d000.usbh-ehci: USB 2.0 started, EHCI 1.00
[ 2.261623] hub 1-0:1.0: USB hub found
[ 2.264128] hub 1-0:1.0: 2 ports detected
[ 2.271138] sii902x 0-0039: Linked as a consumer to regulator.10
[ 2.275873] sii902x 0-0039: Linked as a consumer to regulator.14
[ 2.285972] i2c i2c-0: Added multiplexed i2c bus 2
[ 2.291877] cs42l51 0-004a: Linked as a consumer to regulator.8
[ 2.296511] cs42l51 0-004a: Linked as a consumer to regulator.9
[ 2.305071] cs42l51 0-004a: Cirrus Logic CS42L51, Revision: 01
[ 2.313149] asoc-audio-graph-card sound: cs42l51-hifi0 <-> 4400b004.audio-controller mapping ok
[ 2.321420] asoc-audio-graph-card sound: cs42l51-hifi1 <-> 4400b024.audio-controller mapping ok
[ 2.329603] asoc-audio-graph-card sound: i2s-hifi <-> 4000b000.audio-controller mapping ok
[ 2.338673] cs42l51 0-004a: ASoC: mux DAC Mux has no paths
[ 2.578361] [drm] ltdc hw version 0x00010300 - ready
[ 2.581949] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.588569] [drm] Driver supports precise vblank timestamp query.
[ 2.595423] [drm] Initialized stm 1.0.0 20170330 for 5a001000.display-controller on minor 0
[ 2.604070] stm32_rtc 5c004000.rtc: setting system clock to 2000-01-01 00:00:10 UTC (946684810)
[ 2.612720] vdda: disabling
[ 2.614891] ALSA device list:
[ 2.617562] #0: STM32MP�[ 2.635126] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 2.736622] EXT4-fs (mmcblk0p6): recovery complete
[ 2.741719] EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null)
[ 2.748487] VFS: Mounted root (ext4 filesystem) on device 179:6.
[ 2.761694] devtmpfs: mounted
[ 2.765127] Freeing unused kernel memory: 1024K
[ 2.768530] Run /sbin/init as init process
[ 2.836777] hub 1-1:1.0: USB hub found
[ 2.839200] hub 1-1:1.0: 4 ports detected
[ 3.031097] systemd[1]: System time before build time, advancing clock.
[ 3.132575] NET: Registered protocol family 10
[ 3.176784] Segment Routing with IPv6
[ 3.201409] systemd[1]: systemd 239 running in system mode. (+PAM -AUDIT -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS +ACL +XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD -IDN2 -IDN -PCRE2 default-hierarchy=hybrid)
[ 3.222383] systemd[1]: Detected architecture arm.
Welcome to ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 2.6-openstlinux-19-02-20-github-display-fix (thud)!
[ 3.279439] systemd[1]: Set hostname to <stm32mp1>.
[ 3.292328] systemd[1]: Hardware watchdog 'STM32 Independent Watchdog', version 0
[ 3.299521] systemd[1]: Set hardware watchdog to 30s.
[ 4.057641] systemd[1]: Unnecessary job for dev-ttySTM0.device was removed.
[ 4.065332] random: systemd: uninitialized urandom read (16 bytes read)
[ 4.075488] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 4.115381] random: systemd: uninitialized urandom read (16 bytes read)
[ 4.121715] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 4.155400] random: systemd: uninitialized urandom read (16 bytes read)
[ 4.161477] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 4.197344] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
Starting Load Kernel Modules...
[ OK ] Listening on initctl Compatibility Named Pipe.
[ OK ] Listening on Process Core Dump Socket.
[ OK ] Listening on Network Service Netlink Socket.
[ OK ] Reached target Remote File Systems.
[ OK ] Reached target Swap.
Mounting Temporary Directory (/tmp)...
Mounting Kernel Debug File System...
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Hardware RNG Entropy Gatherer Daemon.
[ 4.590094] random: crng init done
[ 4.592043] random: 7 urandom warning(s) missed due to ratelimiting
Starting Mount partitions...
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Reached target Paths.
[ OK ] Listening on udev Control Socket.
Starting Create list of required st…ce nodes for the current kernel...
Mounting POSIX Message Queue File System...
[ OK ] Listening on Journal Socket (/dev/log).
[ OK ] Listening on udev Kernel Socket.
Starting udev Coldplug all Devices...
[ OK ] Created slice User and Session Slice.
[ 4.942667] EXT4-fs (mmcblk0p4): recovery complete
[ 4.946201] EXT4-fs (mmcblk0p4): mounted filesystem with ordered data mode. Opts: (null)
[ OK ] Reached target Slices.
Starting Remount Root and Kernel File Systems...
Starting Journal Service...
[ 5.130150] EXT4-fs (mmcblk0p6): re-mounted. Opts: (null)
[ OK ] Started Load Kernel Modules.
[ OK ] Mounted Temporary Directory (/tmp).
[ OK ] Mounted Kernel Debug File System.
[ OK ] Started Create list of required sta…vice nodes for the current kernel.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Started Remount Root and Kernel File Systems.
[ OK ] Started Starts Psplash Boot screen.
Starting Create Static Device Nodes in /dev...
Mounting FUSE Control File System...
[ 5.470367] EXT4-fs (mmcblk0p7): recovery complete
[ 5.478220] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
Starting Apply Kernel Variables...
Mounting Kernel Configuration File System...
[ OK ] Started Create Static Device Nodes in /dev.
[ OK ] Started Journal Service.
[ OK ] Mounted FUSE Control File System.
[ OK ] Started Apply Kernel Variables.
[ OK ] Mounted Kernel Configuration File System.
[ 5.829865] EXT4-fs (mmcblk0p5): recovery complete
[ 5.834447] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ OK ] Started Mount partitions.
Starting Flush Journal to Persistent Storage...
Starting udev Kernel Device Manager...
[ OK ] Reached target Local File Systems (Pre).
Mounting /var/volatile...
[ OK ] Reached target Containers.
[ OK ] Started udev Kernel Device Manager.
[ OK ] Mounted /var/volatile.
[ 6.183646] systemd-journald[180]: Received request to flush runtime journal from PID 1
Starting Load/Save Random Seed...
[ OK ] Reached target Local File Systems.
[ OK ] Started Flush Journal to Persistent Storage.
Starting Create Volatile Files and Directories...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
Starting Network Time Synchronization...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Network Time Synchronization.
[ OK ] Reached target System Initialization.
[ OK ] Listening on dropbear.socket.
[ 7.602307] galcore: loading out-of-tree module taints kernel.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ 7.623982] Galcore version 6.2.4.174315
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Listening on RPCbind Server Activation Socket.
Starting Console System Startup Logging...
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
[ OK ] Started D-Bus System Message Bus.
Starting Login Service...
[ OK ] Started System Logging Service.
[ OK ] Started TEE Supplicant.
[ OK ] Started ST Verify if eth0 network interface are already configured.
Starting Network Service...
Starting Enable USB Ethernet gadget...
[ OK ] Started Kernel Logging Service.
Starting Netdata, Real-time performance monitoring...
Starting Weston Wayland Compositor...
Starting Sound Service...
[ OK ] Reached target System Time Synchronized.
[ OK ] Started Console System Startup Logging.
[ 8.898525] using random self ethernet address
[ 8.915176] using random host ethernet address
[ 8.963863] Generic PHY stmmac-0:00: attached PHY driver [Generic PHY] (mii_bus:phy_addr=stmmac-0:00, irq=POLL)
[ 9.060171] dwmac4: Master AXI performs any burst length
[ 9.075201] stm32-dwmac 5800a000.ethernet eth0: No Safety Features support found
[ 9.081214] stm32-dwmac 5800a000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported
[ 9.122692] stm32-dwmac 5800a000.ethernet eth0: registered PTP clock
[ 9.142279] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 9.166994] usb0: HOST MAC aa:c5:02:db:8f:b2
[ 9.169978] usb0: MAC c2:14:c7:ba:bb:74
[ 9.173723] dwc2 49000000.usb-otg: bound driver configfs-gadget
[ OK ] Started Network Service.
[ OK ] Started Sound Service.
[ 9.533638] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready
[ 9.706510] Gcnano is present and activated
[ OK ] Started Enable USB Ethernet gadget.
[ OK ] Started Weston Wayland Compositor.
[ OK ] Started Netdata, Real-time performance monitoring.
[ 14.911651] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 14.951121] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ OK ] Listening on Load/Save RF Kill Switch Status /dev/rfkill Watch.
[ OK ] Reached target Sound Card.
Stopping Network Service...
[ OK ] Started Login Service.
[ OK ] Stopped Network Service.
Starting Network Service...
[ OK ] Started Network Service.
Starting Network Name Resolution...
Starting Wait for Network to be Configured...
[ OK ] Started Network Name Resolution.
[ OK ] Reached target Host and Network Name Lookups.
[ OK ] Reached target Network.
Starting Permit User Sessions...
Starting Target Communication Framework agent...
[ OK ] Started IIO Daemon.
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started Permit User Sessions.
[ OK ] Started Target Communication Framework agent.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Serial Getty on ttySTM0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Reached target Multi-User System.
Starting Update UTMP about System Runlevel Changes...
[ OK ] Started Update UTMP about System Runlevel Changes.
ST OpenSTLinux - Weston - (A Yocto Project Based Distro) 2.6-openstlinux-19-02-20-github-display-fix stm32mp1 ttySTM0
stm32mp1 login: root (automatic login)
root@stm32mp1:~#
Building a Debian System
To be added