Difference between revisions of "Black Pill"

Latest revision as of 02:45, 26 February 2023

The Black Pill development board is a good choice. Of the commercially available development modules, this is one of the best. It was designed by WeAct Studio, but like the Blue Pill many different versions exist. Unlike the Blue Pill, at least at the time of writing this, they all appear to be using genuine STM32 processors (read: no cheaper clones exist). Here are two different ones, both of which I suspect are clones (and both working just fine):

Features

The Black Pills are typically based on a STM32F401 or STM32F411 (both of the above are the F411 version) and offers the following specs:

STM32F4 (STM32F401 or STM32F411) processor
Same footprint (I/O pins)
25 MHz main crystal
32.768 kHz RTC crystal
512 kB Flash (STM32F411 version)
128 kB RAM
1 ADC (no DAC)
USB-C connector
Programming header

Pinout

Flash Layout

EEPROM Footprint

The Black Pill board usually have an unpopulated footprint on the reverse side of the PCB intended for a generic EEPROM:

On the Board Info page, this is documented as:

Unfortunately, the clone Black Pill boards are wired up different. The DO (MISO) is not wired up to PB4 as indicated but rather PA6 (which makes more sense anyway). Using STM32CubeMX, the right configuration is:

USB

The STM32F411 MCU on the Black Pill boards can in principle run in USB Host mode. However, it is worth having a look at the schematics:

Both the CC lines are pulled to GND using a 5.1k resistor, which signals that this is a device, not a host. Also, there is no way to control the power delivery. In short, while the MCU on these boards can operate in USB Host mode, there is no way this can be reliably done on the Black Pill boards.

Miscellaneous Links

Notice, most - if not all - clone boards match the 1.2 schematics.

@@ Line 1: / Line 1: @@
-[[Category:STM32]] [[Category:STM32 Development Board]]
+[[Category:STM32]] [[Category:STM32 Hardware]] [[Category:Development Board]] [[Category:STM32 Development Board]] [[Category:Black Pill]] {{metadesc|WeAct Black Pill V2.0 and clones}}
-The [[Black Pill]] [[STM32 Development Boards|development board]] is a good choice.  As for the [[Blue Pill]] many different versions exist, but unlike the [[Blue Pill]], at least at the time of writing this, they all appear to be using genuine [[STM32]] processors (read: no cheaper clones exist).
+The [[Black Pill]] [[STM32 Development Boards|development board]] is a good choice.  Of the commercially available development modules, this is one of the best.  It was designed by WeAct Studio, but like the [[Blue Pill]] many different versions exist.  Unlike the [[Blue Pill]], at least at the time of writing this, they all appear to be using genuine [[STM32]] processors (read: no cheaper clones exist).  Here are two different ones, both of which I suspect are clones (and both working just fine):
 [[File:Two Different Black Pill Boards.jpg|600px]]
+== Features ==
 The [[Black Pill]]s are typically based on a STM32F401 or STM32F411 (both of the above are the F411 version) and offers the following specs:
@@ Line 10: / Line 12: @@
 * 25 MHz main crystal
 * 32.768 kHz RTC crystal
+* 512 kB Flash (STM32F411 version)
+* 128 kB RAM
+* 1 [[ADC]] (no [[DAC]])
 * USB-C connector
 * Programming header
+== Pinout ==
+<div class="res-img">
+[[File:black pill pinout.png|1400px]]
+</div>
+== Flash Layout ==
+[[File:STM32F411 Flash Sector Layout.png|800px]]
+== EEPROM Footprint ==
+The [[Black Pill]] board usually have an unpopulated footprint on the reverse side of the PCB intended for a generic EEPROM:
+[[File:EEPROM Footprint.png|400px]]
+On the [https://stm32-base.org/boards/STM32F411CEU6-WeAct-Black-Pill-V2.0.html Board Info] page, this is documented as:
+[[File:EEPROM Footprint Documentation.png|800px]]
+Unfortunately, the clone [[Black Pill]] boards are wired up different.  The DO (MISO) is '''not''' wired up to PB4 as indicated but rather PA6 (which makes more sense anyway).  Using [[STM32CubeMX]], the right configuration is:
+[[File:EEPROM Correct Config.png|600px]]
+== USB ==
+The [[STM32F411]] [[MCU]] on the [[Black Pill]] boards can in principle run in USB Host mode.  However, it is worth having a look at the schematics:
+[[File:Black Pill USB Connector Schematics.png|500px]]
+Both the CC lines are pulled to GND using a 5.1k resistor, which signals that this is a device, ''not'' a host.  Also, there is no way to control the power delivery.  In short, while the [[MCU]] on these boards '''can''' operate in USB Host mode, there is no way this can be reliably done on the [[Black Pill]] boards.
+== Miscellaneous Links ==
+* [https://github.com/WeActTC/MiniSTM32F4x1 WeAct Black Pill Github Repository]
+* [https://stm32-base.org/boards/STM32F411CEU6-WeAct-Black-Pill-V2.0.html Board Info]
+* [https://stm32-base.org/assets/pdf/boards/original-schematic-STM32F411CEU6_WeAct_Black_Pill_V2.0.pdf Original Schematics ver. 2.0]
+* [https://stm32-base.org/assets/pdf/boards/original-schematic-STM32F401CCU6_WeAct_Black_Pill_V1.2.pdf Original Schematics vers. 1.2]
+* [https://www.st.com/resource/en/datasheet/stm32f411ce.pdf STM32F411x Datasheet]
+* [https://ipfs.io/ipfs/QmUGduV94vdwiX5FpM5uAbNPBNw48gFXgJZyFJFeLJrbws/dm00119316-stm32f411xc-e-advanced-arm-based-32-bit-mcus-stmicroelectronics.pdf STM32F411xC/E advanced Arm®-based 32-bit MCUs Reference Manual]
+* [https://github.com/trebisky/stm32f411 Bare metal coding on the STM32F411/Black Pill]
+Notice, most - if not all - clone boards match the 1.2 schematics.