Demiurge/Standard Blocks

All blocks has a single Output signal, to which an Input on another block can be connected. The rare cases of multiple Output blocks, such as #Pan, and accomplishes this by having sub-blocks for each Output that downstream blocks can be connected to.

ADSR - Attack, Decay, Sustain, Release

Source Code

Inputs

Name	Description
attack	Sets the attack time of the ADSR function
decay	Sets the decay time of the ADSR function
sustain	Sets the sustain level of the ADSR function
release	Sets the release time of the ADSR function
gate	Gate signal for the ADSR function
trig	Re-trig signal for the ADSR function

Audio Inport

Source Code

Inputs

Name	Description
None

Audio Outport

Source Code

Inputs

Name	Description
input	The audio signal to be set to the physical output port as an audio signal.

Averager

Source Code

Inputs

Name	Description
input	The signal to be averaged.
averaging_control	The amount of averging to be applied to the signal.

Calculator

Source Code

Inputs

Name	Description
input	The signal to apply the [***Function***](functions.md) on.

CFX RBJ Filter

Source Code

Inputs

Name	Description
input	Signal to be filtered
frequency	Frequency to be filtered at
Q	Q factor which sets slope and ringing
gain	Gain/attenuation in the filter
type	0 - low pass 1 - high pass 2 - bandpass (csg) 3 - bandpass (czpg) 4 - notch 5 - allpass 6 - peaking 7 - low shelf 8 - high shelf

Control Pair

Source Code

Inputs

Name	Description
None

CV Inport

Source Code

Inputs

Name	Description
None

CV Outport

Source Code

Inputs

Name	Description
input	The signal to be set to the physical output prot as a CV signal

Fixed Signal

Source Code

Inputs

Name	Description
None

Gate Inport

Source Code

Inputs

Name	Description
input	The audio signal to be set to the physical output port as an audio signal.

Gate Outport

Source Code

Inputs

Name	Description
input	The signal to be set to the physical output prot as a Gate signal.

Inverter

Source Code

Inputs

Name	Description
input	The signal to be inverted.
scale	Scaling of the signal.
offset	Offset around which the signal should be inverted.

LED

Source Code

Inputs

Name	Description
input	The RGB value of the LED to be set. Only used if r, g and b are not configured.
r	The RED value to be set to the physical LED.
g	The GREEN value to be set to the physical LED.
b	The BLUE value to be set to the physical LED.

Lg

Source Code

Inputs

Name	Description
input	The signal that will have ln (the natural logarithm) applied to it.

Lg2

Source Code

Inputs

Name	Description
The signal that will have log2 applied to it.

Lg10

Source Code

Inputs

Name	Description
The signal that will have log10 applied to it.

Mixer

Source Code

Inputs

Name	Description
inputs[]	An array of signals to be mixed to the Output.
volumes[]	An array of volume controllers, one for each Input.

Offset

Source Code

Inputs

Name	Description
input	The signal to be offsetted
offset_control	The amount of offset to be applied to the ***Input***

Oscillator

The Oscillator is a block that generates waveforms at a controllable frequency and amplitude. The start of the waveform is also controllable with the *trigger*, but should be used with caution as it introduces spike frequencies.

Source Code

Inputs

Name	Description
frequency	The frequency to generate. For non-SINE, it is the inverse of the full cycle period.
amplitude	The amplitude of the output signal.
trigger	Re-trigger the wave generation to time zero.

Pan

Source Code

Inputs

Name	Description
input	The signal to be split in a *left* and *right* channel.
control	The balance between *left* (0V) and *right* (10V) channel.

Sub-blocks

Name	Description
left_channel
right_channel

Passthru

Source Code

Inputs

Name	Description
input	The signal to be pass to the output.

Potentiometer

Source Code

Inputs

Name	Description
None

Push Button

Source Code

Inputs

Name	Description
None

Scale

Source Code

Inputs

Name	Description
input	The signal to be scaled.
control	The amplication/attenuation control. 0V=muted, 10V=~20dB gain

State Variable Filter

Source Code

Inputs

Name	Description
input	Signal to be filtered.
frequency	Frequency to be filtered at.
Q	Q factor which sets slope and ringing.
gain	Gain/attenuation in the filter.

Sub-blocks

Name	Description
lowpass_out	Low pass filter output signal.
highpass_out	High pass filter output signal.
bandpass_out	Bandpass filter output signal.
notch_out	Notch filter output signal.

Volume

Source Code

Inputs

Name	Description
Signal to be volume controlled. |
The amplification/attenuation control. output=input*(0.05 * control + 0.5) |