Serial Flash - W25Qxxx QuadSPI
Jump to navigation
Jump to search
STM32L4 training - Hands-on QSPI
Source Example
Working:
QSPI_CommandTypeDef sCommand;
static uint8_t id[17] = { 0 };
static uint8_t tx_buf[0x10] = "Ext Flash";
static uint8_t rx_buf[0x10] = { 0 };
sCommand.DdrMode = QSPI_DDR_MODE_DISABLE;
sCommand.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
sCommand.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
/***** Read ID operation*****/
sCommand.Instruction = 0x9F; //READ ID command code
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_NONE; //Address line width. No address phase
sCommand.DataMode = QSPI_DATA_1_LINE; //Data line width
sCommand.NbData = 17; //Read the data length. ID length is 17 bytes
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 0; //No Dummy phase
//Configuration command (when there is data stage, the command will be sent in the subsequent sending/receiving API call)
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
//Execute QSPI reception
if (HAL_QSPI_Receive(&hqspi, id, 5000) != HAL_OK) {
Error_Handler();
}
/***** Write enable operation (need to make the external memory in the write enable state before block erasing) *****/
sCommand.Instruction = 0x06; //Write enable command code
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_NONE; //Address line width. No address phase
sCommand.DataMode = QSPI_DATA_NONE; //Data line width. No data stage
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 0; //No Dummy phase
//Configure sending command
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
/***** Block erase operation*****/
sCommand.Instruction = 0xD8; //Sector erase command code
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_1_LINE; //Address line width. No address phase
sCommand.AddressSize = QSPI_ADDRESS_24_BITS; //Address length
sCommand.Address = 0; //Any address in the sector to be erased.
sCommand.DataMode = QSPI_DATA_NONE; //Data line width. No data stage
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 0; //No Dummy phase
//Configure sending command
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
HAL_Delay(3000); //Delay 3s. The unit is SysTick timer interrupt period
/***** Write enable operation (need to make the external memory in the write enable state before block erasing) *****/
sCommand.Instruction = 0x06; //Write enable command code
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_NONE; //Address line width. No address phase
sCommand.DataMode = QSPI_DATA_NONE; //Data line width. No data stage
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 0; //No Dummy phase
//Configure sending command
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
/***** Four-wire fast write operation*****/
sCommand.Instruction = 0x32; //Quick write command code with four lines
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_1_LINE; //Address line width
sCommand.AddressSize = QSPI_ADDRESS_24_BITS; //Address length
sCommand.Address = 0; //Write the starting address
sCommand.DataMode = QSPI_DATA_4_LINES; //Data line width
sCommand.NbData = 10; //write data length
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 0; //No Dummy phase
//Configuration command (when there is data stage, the command will be sent in the subsequent sending/receiving API call)
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
//Execute QSPI reception
if (HAL_QSPI_Transmit(&hqspi, tx_buf, 5000) != HAL_OK) {
Error_Handler();
}
HAL_Delay(5); //Delay 5ms. The unit is SysTick timer interrupt period
/***** Four-wire fast read operation*****/
sCommand.Instruction = 0x6B; //Quick read command code with four lines
sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; //Command line width
sCommand.AddressMode = QSPI_ADDRESS_1_LINE; //Address line width
sCommand.AddressSize = QSPI_ADDRESS_24_BITS; //Address length
sCommand.Address = 0; //Start address
sCommand.DataMode = QSPI_DATA_4_LINES; //Data line width
sCommand.NbData = 10; //Read data length
sCommand.AlternateByteMode = QSPI_ALTERNATE_BYTES_NONE; //No multiplexing byte stage
sCommand.DummyCycles = 8; //Dummy phase. N25Q128A13EF840F
//Configuration command (when there is data stage, the command will be sent in the subsequent sending/receiving API call)
if (HAL_QSPI_Command(&hqspi, &sCommand, 5000) != HAL_OK) {
Error_Handler();
}
//Execute QSPI reception
if (HAL_QSPI_Receive(&hqspi, rx_buf, 5000) != HAL_OK) {
Error_Handler();
}