STM32 SD card with FatFs

Micro-SD Adaptor with jumper leads soldered on

In this article we will be interfacing a SD-card using STM32.

For this purpose we have modified a SD to Micro-SD adaptor by soldering 9 jumper leads on it (see photo on the right).

SD-Card Pinout

The pinout of a SD-card and a MicroSD-card are as follows:

It is important to notice that all SD-cards can be interfaced in two different ways:

1. SDIO
2. SPI

DIY SD-card Adaptor

A quick way to hook up a SD-card to a STM32 is to use one of those SD to Micro-SD adaptors that come with most Micro-SD's when you buy them. I made one looking like this:

Combining that with the pinout from the previous section, we can make the following table:

Pin	Color	SDIO	SPI
1	White	CD/Dat3	CS
2	Grey	CMD	DI
3	Purple	VSS1	VSS1
4	Blue	VDD	VDD
5	Green	CLK	SCLK
6	Yellow	VSS2	VSS2
7	Orange	DAT0	DO
8	Red	DAT1
9	Black	DAT2

As per the SD-card specification in both the case of SPI and SDIO, all signals except the clock should be pulled up. Our DIY adaptor does not include pull-up resistors, so we will have to rely on the internal ones, which are really quite weak but as long as the leads are not too long it should work ok.

SPI

NOTICE! While it is supported by most, some SD-cards do not support SPI access. If this fails for you, try with another card. Older cards are more likely to work.

SDIO

Some MCUs - for example the STM32F405 - includes a SDIO peripheral which can be used to drive a SD-card directly. Schematics will look like this:

Notice the pull-up resistors on all lines except the CLK.

On a PCB that could look like this:

The SDIO can be configured using STM32CubeMX like this:

4-bit

For some reason that I am not entirely clear about, SD cards must be initialized with 1-bit mode only and then switched to 4-bit. The easiest way to do this is to configure it as 4-bit in STM32CubeMX and then modify the 'MX_SDIO_SD_Init' function like this:

/**
 * @brief SDIO Initialization Function
 * @param None
 * @retval None
 */
static void MX_SDIO_SD_Init(void)
{

    /* USER CODE BEGIN SDIO_Init 0 */

    /* USER CODE END SDIO_Init 0 */

    /* USER CODE BEGIN SDIO_Init 1 */

    /* USER CODE END SDIO_Init 1 */
    hsd.Instance = SDIO;
    hsd.Init.ClockEdge = SDIO_CLOCK_EDGE_RISING;
    hsd.Init.ClockBypass = SDIO_CLOCK_BYPASS_ENABLE;
    hsd.Init.ClockPowerSave = SDIO_CLOCK_POWER_SAVE_DISABLE;
    hsd.Init.BusWide = SDIO_BUS_WIDE_4B;
    hsd.Init.HardwareFlowControl = SDIO_HARDWARE_FLOW_CONTROL_DISABLE;
    hsd.Init.ClockDiv = 0;
    /* USER CODE BEGIN SDIO_Init 2 */

    // First init with 1B bus - SD card will not initialize with 4 bits
    hsd.Init.BusWide = SDIO_BUS_WIDE_1B;
    if (HAL_SD_Init(&hsd) != HAL_OK) {
        Error_Handler();
    }

    // Now we can switch to 4 bit mode
    if (HAL_SD_ConfigWideBusOperation(&hsd, SDIO_BUS_WIDE_4B) != HAL_OK) {
        Error_Handler();
    }

    /* USER CODE END SDIO_Init 2 */

}

Gallery

The following quick "hack" was soldered together and it works flawlessly.

• 
• 
• 
• 
• 
• 

Miscellaneous Links

• SPI SD Card Example