Difference between revisions of "DFRobot 10 DOF"
Jump to navigation
Jump to search
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:STM32]][[Category:STM32 Development]][[Category:Components and Modules]][[Category:STM32CubeMX]][[Category:STM32CubeIde]][[Category:I²C]]{{metadesc|How to use a 10 DOF MEMS IMU sensor module with STM32}}[[File:DFRobot 10 DOF v1.0.jpg|thumb| | + | [[Category:STM32]][[Category:STM32 Development]][[Category:Components and Modules]][[Category:STM32CubeMX]][[Category:STM32CubeIde]][[Category:I²C]]{{metadesc|How to use a 10 DOF MEMS IMU sensor module with STM32}}[[File:DFRobot 10 DOF v1.0.jpg|thumb|400px]] |
The DFRobot 10 DOF sensor module contains 4 different [[I²C]] sensors: | The DFRobot 10 DOF sensor module contains 4 different [[I²C]] sensors: | ||
| Line 20: | Line 20: | ||
== {{I2C}} bus == | == {{I2C}} bus == | ||
| + | |||
| + | The four sensors show up on the {{I2C}} bus like this: | ||
<pre> | <pre> | ||
| Line 57: | Line 59: | ||
=== ITG3200 Documentation === | === ITG3200 Documentation === | ||
| + | * [https://product.tdk.com/system/files/dam/doc/product/sensor/mortion-inertial/gyro/data_sheet/itg-3200-datasheet.pdf ITG3200 Product Specification] | ||
* [https://invensense.tdk.com/wp-content/uploads/2015/02/ITG-3200-Register-Map.pdf ITG3200 Register Map & Register Descriptions] | * [https://invensense.tdk.com/wp-content/uploads/2015/02/ITG-3200-Register-Map.pdf ITG3200 Register Map & Register Descriptions] | ||
Latest revision as of 05:18, 3 October 2024
The DFRobot 10 DOF sensor module contains 4 different I²C sensors:
- Adxl345 accelerometer
- ITG3200 gyro
- HMC5883L Compass
- BMP085 pressure sensor
Each of these sensors will be handled on a separate page but a general overview follows on this page.
Schematics
DFRobot provides schematics for most of their product. The schematic for the 10 DOF board is this:
As can be seen, all four sensors are wired up to the same I²C bus. It's a pity the individual interrupt lines are not wired out to the header as that would have made the board a LOT more usable.
I²C bus
The four sensors show up on the I²C bus like this:
Scan i2c2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1e -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 53 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 77 -- -- -- -- -- -- -- --
| ID | Device |
|---|---|
| 0x1e | HMC5883L Compass |
| 0x53 | ADXL345 Accelerometer |
| 0x68 | ITG3200 Gyro |
| 0x77 | BMP085 Pressure/Temperature Sensor |