Difference between revisions of "Black Pill"

Latest revision as of 12:07, 11 November 2024

Blackpill board with ST-Link

The Black Pill development board is a good choice. Of the commercially available development modules, this is one of the best. It was designed by WeAct Studio, but like the Blue Pill many different versions exist. Unlike the Blue Pill, at least at the time of writing this, they all appear to be using genuine STM32 processors (read: no cheaper clones exist). Here are two different ones, both of which I suspect are clones (and both working just fine):

Videos

The Black Pill board is used in several (not all) of our tutorial videos.

You can watch the video on youtube here: https://www.youtube.com/watch?v=O6cNvE9ZrVU (full series here).

Features

The Black Pills are typically based on a STM32F401 or STM32F411 (both of the above are the F411 version) and offers the following specs:

STM32F4 (STM32F401 or STM32F411) processor
Same footprint (I/O pins)
25 MHz main crystal
32.768 kHz RTC crystal
512 kB Flash (STM32F411 version)
128 kB RAM
1 ADC (no DAC)
USB-C connector
Programming header

Pinout

Built-in LED

Notice, the Black Pill board have got a built-in LED attached to PC13. This is perfectly Ok, if you want to toggle the LED on or off. Unfortunately, no timer channel is connected to this pin, so it is not normally possible to regulate the intensity using PWM. Fortunately, it is possible to do PWM by bit-banging the pin. See STM32 bit bang PWM for an explanation on how this can be done.

Flash Layout

EEPROM Footprint

The Black Pill board usually have an unpopulated footprint on the reverse side of the PCB intended for a generic EEPROM:

On the Board Info page, this is documented as:

Unfortunately, the clone Black Pill boards are wired up different. The DO (MISO) is not wired up to PB4 as indicated but rather PA6 (which makes more sense anyway). Using STM32CubeMX, the right configuration is:

USB

The STM32F411 MCU on the Black Pill boards can in principle run in USB Host mode. However, it is worth having a look at the schematics:

Both the CC lines are pulled to GND using a 5.1k resistor, which signals that this is a device, not a host. Also, there is no way to control the power delivery. In short, while the MCU on these boards can operate in USB Host mode, there is no way this can be reliably done on the Black Pill boards.

Miscellaneous Links

Notice, most - if not all - clone boards match the 1.2 schematics.

@@ Line 1: / Line 1: @@
 [[Category:STM32]] [[Category:STM32 Hardware]] [[Category:Development Board]] [[Category:STM32 Development Board]] [[Category:Black Pill]] {{metadesc|WeAct Black Pill V2.0 and clones}}
+[[File:Blackpill with st-link.jpg|300px|thumb|Blackpill board with [[DIY STM32 Programmer (ST-Link/V2-1)|ST-Link]]]]
 The [[Black Pill]] [[STM32 Development Boards|development board]] is a good choice.  Of the commercially available development modules, this is one of the best.  It was designed by WeAct Studio, but like the [[Blue Pill]] many different versions exist.  Unlike the [[Blue Pill]], at least at the time of writing this, they all appear to be using genuine [[STM32]] processors (read: no cheaper clones exist).  Here are two different ones, both of which I suspect are clones (and both working just fine):
 [[File:Two Different Black Pill Boards.jpg|600px]]
+== Videos ==
+The [[Black Pill]] board is used in several (not all) of our tutorial videos.
+You can watch the video on youtube here: [https://www.youtube.com/watch?v=O6cNvE9ZrVU https://www.youtube.com/watch?v=O6cNvE9ZrVU] (full series [[STM32 Getting Started Tutorial Video Series (by STM32World)|here]]).
+{{#ev:youtube|O6cNvE9ZrVU}}
 == Features ==