Difference between revisions of "DFRobot 10 DOF"
Jump to navigation
Jump to search
| (18 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | [[Category:STM32]][[Category:STM32 Development]][[Category:Components and Modules]][[Category:STM32CubeMX]][[Category:STM32CubeIde]][[Category:I²C]]{{metadesc|How to use a 10 DOF MEMS IMU sensor module with STM32}}[[File:DFRobot 10 DOF v1.0.jpg|thumb| | + | [[Category:STM32]][[Category:STM32 Development]][[Category:Components and Modules]][[Category:STM32CubeMX]][[Category:STM32CubeIde]][[Category:I²C]]{{metadesc|How to use a 10 DOF MEMS IMU sensor module with STM32}}[[File:DFRobot 10 DOF v1.0.jpg|thumb|400px]] |
The DFRobot 10 DOF sensor module contains 4 different [[I²C]] sensors: | The DFRobot 10 DOF sensor module contains 4 different [[I²C]] sensors: | ||
| Line 8: | Line 8: | ||
Each of these sensors will be handled on a separate page but a general overview follows on this page. | Each of these sensors will be handled on a separate page but a general overview follows on this page. | ||
| + | |||
| + | == Schematics == | ||
| + | |||
| + | DFRobot provides schematics for most of their product. The schematic for the 10 DOF board is this: | ||
| + | |||
| + | <div class="res-img"> | ||
| + | [[File:10_DOF_Schematic.png]] | ||
| + | </div> | ||
| + | |||
| + | As can be seen, all four sensors are wired up to the same {{I2C}} bus. It's a pity the individual interrupt lines are not wired out to the header as that would have made the board a LOT more usable. | ||
| + | |||
| + | == {{I2C}} bus == | ||
| + | |||
| + | The four sensors show up on the {{I2C}} bus like this: | ||
| + | |||
| + | <pre> | ||
| + | Scan i2c2 | ||
| + | -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| + | -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1e -- | ||
| + | -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| + | -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| + | -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- | ||
| + | -- -- -- 53 -- -- -- -- -- -- -- -- -- -- -- -- | ||
| + | -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- | ||
| + | -- -- -- -- -- -- -- 77 -- -- -- -- -- -- -- -- | ||
| + | </pre> | ||
| + | |||
| + | {| class="wikitable" | ||
| + | |- | ||
| + | ! ID | ||
| + | ! Device | ||
| + | |- | ||
| + | | 0x1e | ||
| + | | [[#HMC5883L Compass|HMC5883L Compass]] | ||
| + | |- | ||
| + | | 0x53 | ||
| + | | [[#Adxl345 Accelerometer|ADXL345 Accelerometer]] | ||
| + | |- | ||
| + | | 0x68 | ||
| + | | [[#ITG3200 Gyro|ITG3200 Gyro]] | ||
| + | |- | ||
| + | | 0x77 | ||
| + | | [[#BMP085 Pressure/Temperature Sensor|BMP085 Pressure/Temperature Sensor]] | ||
| + | |} | ||
| + | |||
| + | == Adxl345 Accelerometer == | ||
| + | |||
| + | == ITG3200 Gyro == | ||
| + | |||
| + | === ITG3200 Documentation === | ||
| + | |||
| + | * [https://product.tdk.com/system/files/dam/doc/product/sensor/mortion-inertial/gyro/data_sheet/itg-3200-datasheet.pdf ITG3200 Product Specification] | ||
| + | * [https://invensense.tdk.com/wp-content/uploads/2015/02/ITG-3200-Register-Map.pdf ITG3200 Register Map & Register Descriptions] | ||
| + | |||
| + | == HMC5883L Compass == | ||
| + | |||
| + | == BMP085 Pressure/Temperature Sensor == | ||
| + | |||
| + | |||
== Miscellaneous Links == | == Miscellaneous Links == | ||
| Line 13: | Line 72: | ||
* [https://wiki.dfrobot.com/10_DOF_Sensor__SKU_SEN0140_ DFRobot Wiki Page] | * [https://wiki.dfrobot.com/10_DOF_Sensor__SKU_SEN0140_ DFRobot Wiki Page] | ||
* [https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL345.pdf ADXL345 Datasheet] | * [https://www.analog.com/media/en/technical-documentation/data-sheets/ADXL345.pdf ADXL345 Datasheet] | ||
| − | * [https:// | + | * [https://product.tdk.com/system/files/dam/doc/product/sensor/mortion-inertial/gyro/data_sheet/itg-3200-datasheet.pdf ITG-3200 Product Specification] |
| − | * [https:// | + | * [https://cdn-shop.adafruit.com/datasheets/HMC5883L_3-Axis_Digital_Compass_IC.pdf HMC5883L Datasheet] |
| − | * [https:// | + | * [https://www.sparkfun.com/datasheets/Components/General/BST-BMP085-DS000-05.pdf BMP085 Datasheet] |
Latest revision as of 05:18, 3 October 2024
The DFRobot 10 DOF sensor module contains 4 different I²C sensors:
- Adxl345 accelerometer
- ITG3200 gyro
- HMC5883L Compass
- BMP085 pressure sensor
Each of these sensors will be handled on a separate page but a general overview follows on this page.
Schematics
DFRobot provides schematics for most of their product. The schematic for the 10 DOF board is this:
As can be seen, all four sensors are wired up to the same I²C bus. It's a pity the individual interrupt lines are not wired out to the header as that would have made the board a LOT more usable.
I²C bus
The four sensors show up on the I²C bus like this:
Scan i2c2 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 1e -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 53 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 77 -- -- -- -- -- -- -- --
| ID | Device |
|---|---|
| 0x1e | HMC5883L Compass |
| 0x53 | ADXL345 Accelerometer |
| 0x68 | ITG3200 Gyro |
| 0x77 | BMP085 Pressure/Temperature Sensor |